Sometimes you might want to have a filled object with a hole in it.
Now use the WildTools Combine tool to add the slicer to the hole.
...and the WildTools Clip tool to subtract the new (slicer+hole) object from the donut.
and delete the slicer..
Reshape the nearby points on the donut to close the gap.
Now you can give the donut a fill. I find it's best to set the line to NIL
and create new edges if I want to define them with lines. Otherwise PowerCADD will put a line over the connecting channel.
you can add a gradient and some highlights if you have a hankering..
The technique is not limited to drawing confectionary however.
But PowerCADD is reluctant... With two objects, the donut and the hole, draw a third object, a slicer. I keep mine thin. It must overlap the donut object and the hole object, and extend past the donut to the exterior.
. There's a Hole in My Donut
There's a Hole in My Donut
Two other Options to get the filled donut that I believe uses fewer steps and is quicker
Option A: WildTools Thicken Tool
With the two circles drawn (donut edge and hole):
1. Option+Click on WTools Thicken Tool and set to INTERACTIVE
2. Drag from Outer donut circle toward donut hole
3. Press "S" for surface snap and the donut (sans hole) is filled with a new polygon
Option B: PowerCADD Paint Bucket Tool
With the two circles drawn (donut edge and hole):
1. Select the Paint Bucket tool
2. Click inside, between the donut and the hole
3. The donut is filled
Render "to taste" as described in original post
No need to draw any extra objects nor reshape the polygon to close it up.
Personally, I find the WT Thicken tool creates a cleaner polygon with fewer vertices but both methods work. In particular, the Polygon created with WT Thicken has fewer crossing segments which is helpful when applying things like gradients. I often find it useful to use Tool menu > Polygon... > Thin Polygon (or Distribute points then Thin depending on the complexity of the shape) as it helps reduce the # of vertices and can eliminate problems if exporting to PDF, particularly if reducing drawings. PDF historically doesn't like vertices that cross over each other and when creating the Bézier curves in some cases things get a little messed up
Always nice to have more than one way to skin a cat!
Pity that PCADD lost the ability to do that same operation with Hatching. In earlier versions, it was possible to just select the two objects (donut and hole) and choose HATCH... it would hatch the donut, leaving the hole.
Option A: WildTools Thicken Tool
With the two circles drawn (donut edge and hole):
1. Option+Click on WTools Thicken Tool and set to INTERACTIVE
2. Drag from Outer donut circle toward donut hole
3. Press "S" for surface snap and the donut (sans hole) is filled with a new polygon
Option B: PowerCADD Paint Bucket Tool
With the two circles drawn (donut edge and hole):
1. Select the Paint Bucket tool
2. Click inside, between the donut and the hole
3. The donut is filled
Render "to taste" as described in original post
No need to draw any extra objects nor reshape the polygon to close it up.
Personally, I find the WT Thicken tool creates a cleaner polygon with fewer vertices but both methods work. In particular, the Polygon created with WT Thicken has fewer crossing segments which is helpful when applying things like gradients. I often find it useful to use Tool menu > Polygon... > Thin Polygon (or Distribute points then Thin depending on the complexity of the shape) as it helps reduce the # of vertices and can eliminate problems if exporting to PDF, particularly if reducing drawings. PDF historically doesn't like vertices that cross over each other and when creating the Bézier curves in some cases things get a little messed up
Always nice to have more than one way to skin a cat!
Pity that PCADD lost the ability to do that same operation with Hatching. In earlier versions, it was possible to just select the two objects (donut and hole) and choose HATCH... it would hatch the donut, leaving the hole.
- Attachments
-
- start with the donut edge and the hole
- 1.jpg (170.96 KiB) Viewed 38304 times
-
- option + click to set thicken tool to interactive
- 2.jpg (165.12 KiB) Viewed 38304 times
-
- while dragging with thicken tool - use S snap to match inside donut hole surface
- 3.jpg (175.54 KiB) Viewed 38304 times